new high-speed USB device number 15 using xhci_hcd
[ 3057.678375] usb 1-1: New USB device found, idVendor=0781, idProduct=5572, bcdDevice= 1.26
[ 3057.678391] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3057.678397] usb 1-1: Product: Cruzer Switch
[ 3057.678402] usb 1-1: Manufacturer: SanDisk
[ 3057.678406] usb 1-1: SerialNumber: 4C530009621026105083
[ 3057.680019] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 3057.680515] scsi host3: usb-storage 1-1:1.0
[ 3058.710546] scsi 3:0:0:0: Direct-Access SanDisk Cruzer Switch 1.26 PQ: 0 ANSI: 6
[ 3058.711546] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 3058.712736] sd 3:0:0:0: [sdb] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 3058.714576] sd 3:0:0:0: [sdb] Write Protect is off
[ 3058.714592] sd 3:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 3058.714981] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn’t support DPO or FUA
[ 3068.780199] usb 1-1: USB disconnect, device number 15
[ 3068.793159] print_req_error: 2 callbacks suppressed
[ 3068.793162] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793168] buffer_io_error: 2 callbacks suppressed
[ 3068.793169] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793232] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793237] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793247] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793250] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793253] ldm_validate_partition_table(): Disk read failed.
[ 3068.793258] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793260] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793266] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793267] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793273] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793275] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793280] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793282] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793285] Dev sdb: unable to read RDB block 0
[ 3068.793289] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793291] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793296] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793298] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3068.793308] blk_update_request: I/O error, dev sdb, sector 24 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 3068.793311] Buffer I/O error on dev sdb, logical block 3, async page read
[ 3068.793323] sdb: unable to read partition table
[ 3068.821151] sd 3:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 3068.821158] sd 3:0:0:0: [sdb] Sense not available.
[ 3068.821165] sd 3:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 3068.821175] sdb: detected capacity change from 31266816 to 0
[ 3068.821180] sd 3:0:0:0: [sdb] Attached SCSI disk
Hi @Soleiman,
Please be informed that our drivers are preferred to use in Windows and Mac only as drives are tested only in Windows and Mac OS.
If further assistance is needed, please open a case with our support team at the following:
https://kb.sandisk.com/app/ask
