# What does “SMART ATA Error Log Structure error: invalid SMART checksum.” mean? **URL:** \ **Category:** WD\_BLACK | Blue | Red | Green | Gold SSD\ **Created:** [June 11, 2024, 5:18pm UTC](https://forums.sandisk.com/t/what-does-smart-ata-error-log-structure-error-invalid-smart-checksum-mean/319401 "2024-06-11T17:18:18Z")\ **Posts on this page:** 3\ **Page:** 1
**Author:** ![manueljordan](https://avatars.discourse-cdn.com/v4/letter/m/ecae2f/32.png) [@manueljordan](https://forums.sandisk.com/u/manueljordan)\ **Post date:** [June 11, 2024, 5:18pm UTC](https://forums.sandisk.com/t/what-does-smart-ata-error-log-structure-error-invalid-smart-checksum-mean/319401/1 "2024-06-11T17:18:18Z")
I bought 6 SSD of this model - [Western Digital 1TB WD Blue SA510 SATA Internal Solid State Drive SSD - SATA III 6 Gb/s, 2.5"/7mm, Up to 560 MB/s - WDS100T3B0A](https://www.amazon.com/Western-Digital-SA510-Internal-Solid/dp/B09ZYQ84CM) so far one was installed due a tight time due work I have a situation about this SSD reported at (pls read it to be able to see the Figures): - [What does “SMART ATA Error Log Structure error: invalid SMART checksum.” mean?](https://itsfoss.community/t/what-does-smart-ata-error-log-structure-error-invalid-smart-checksum-mean/12164) This SSD is working in a Toshiba’s laptop and has installed Linux Ubuntu 22.04 To have a better idea about the situation - I did do a research in the web and is suggested work with the `smartctl` command and `GSMartControl` GUI As follows the reports: **sudo smartctl -H /dev/sda1** ```bash sudo smartctl -H /dev/sda1 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.5.0-35-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED ``` **sudo smartctl -H /dev/sda2** ```bash sudo smartctl -H /dev/sda2 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.5.0-35-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED ``` So far all seem fine **sudo smartctl -a /dev/sda1** ```bash sudo smartctl -a /dev/sda1 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.5.0-35-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WD Blue SA510 2.5 1000GB Serial Number: 22196N807187 LU WWN Device Id: 5 001b44 8b08f5266 Firmware Version: 52008100 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 9 10:45:21 2024 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 5 Reallocated_Sector_Ct 0x0032 100 100 010 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 2 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1057 165 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 98173724 166 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 167 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 17 168 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 1 169 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 236 170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 171 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 172 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 173 Unknown_Attribute 0x0032 100 100 005 Old_age Always - 0 174 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 742 184 End-to-End_Error 0x0032 100 100 097 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 194 Temperature_Celsius 0x0022 100 100 014 Old_age Always - 32 (Min/Max 17/39) 199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0 230 Unknown_SSD_Attribute 0x0032 100 100 000 Old_age Always - 1524713390435 232 Available_Reservd_Space 0x0033 100 100 004 Pre-fail Always - 94 233 Media_Wearout_Indicator 0x0032 100 100 000 Old_age Always - 0 234 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 16429 241 Total_LBAs_Written 0x0030 253 253 000 Old_age Offline - 530 242 Total_LBAs_Read 0x0030 253 253 000 Old_age Offline - 382 244 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 Warning! SMART ATA Error Log Structure error: invalid SMART checksum. SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 2 - # 2 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. ``` **sudo smartctl -a /dev/sda2** ```bash sudo smartctl -a /dev/sda2 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.5.0-35-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WD Blue SA510 2.5 1000GB Serial Number: 22196N807187 LU WWN Device Id: 5 001b44 8b08f5266 Firmware Version: 52008100 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 9 10:47:52 2024 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 5 Reallocated_Sector_Ct 0x0032 100 100 010 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 2 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1057 165 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 98632477 166 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 167 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 17 168 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 1 169 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 236 170 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 171 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 172 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 173 Unknown_Attribute 0x0032 100 100 005 Old_age Always - 0 174 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 742 184 End-to-End_Error 0x0032 100 100 097 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 194 Temperature_Celsius 0x0022 100 100 014 Old_age Always - 33 (Min/Max 17/39) 199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0 230 Unknown_SSD_Attribute 0x0032 100 100 000 Old_age Always - 1524713390435 232 Available_Reservd_Space 0x0033 100 100 004 Pre-fail Always - 94 233 Media_Wearout_Indicator 0x0032 100 100 000 Old_age Always - 0 234 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 16467 241 Total_LBAs_Written 0x0030 253 253 000 Old_age Offline - 530 242 Total_LBAs_Read 0x0030 253 253 000 Old_age Offline - 382 244 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 Warning! SMART ATA Error Log Structure error: invalid SMART checksum. SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 2 - # 2 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. ``` **sudo smartctl -x /dev/sda1** ```bash sudo smartctl -x /dev/sda1 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.5.0-35-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WD Blue SA510 2.5 1000GB Serial Number: 22196N807187 LU WWN Device Id: 5 001b44 8b08f5266 Firmware Version: 52008100 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 9 10:49:42 2024 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 2 12 Power_Cycle_Count -O--CK 100 100 000 - 1057 165 Unknown_Attribute -O--CK 100 100 000 - 99025695 166 Unknown_Attribute -O--CK 100 100 000 - 0 167 Unknown_Attribute -O--CK 100 100 000 - 17 168 Unknown_Attribute -O--CK 100 100 000 - 1 169 Unknown_Attribute -O--CK 100 100 000 - 236 170 Unknown_Attribute -O--CK 100 100 000 - 0 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 173 Unknown_Attribute -O--CK 100 100 005 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 742 184 End-to-End_Error -O--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 014 - 34 (Min/Max 17/39) 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 230 Unknown_SSD_Attribute -O--CK 100 100 000 - 1524713390435 232 Available_Reservd_Space PO--CK 100 100 004 - 94 233 Media_Wearout_Indicator -O--CK 100 100 000 - 0 234 Unknown_Attribute -O--CK 100 100 000 - 16499 241 Total_LBAs_Written ----CK 253 253 000 - 530 242 Total_LBAs_Read ----CK 253 253 000 - 382 244 Unknown_Attribute -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate ||| ____ S speed/performance || _____ O updated online | ______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa7 GPL,SL VS 1 Device vendor specific log 0xde GPL,SL VS 1 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 2 - # 2 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (empty) == 0x05 ===== = = === == Temperature Statistics (empty) == 0x07 ===== = = === == Solid State Device Statistics (empty) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC ``` **sudo smartctl -x /dev/sda2** ```bash sudo smartctl -x /dev/sda2 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.5.0-35-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WD Blue SA510 2.5 1000GB Serial Number: 22196N807187 LU WWN Device Id: 5 001b44 8b08f5266 Firmware Version: 52008100 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 9 10:51:02 2024 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 2 12 Power_Cycle_Count -O--CK 100 100 000 - 1057 165 Unknown_Attribute -O--CK 100 100 000 - 99287840 166 Unknown_Attribute -O--CK 100 100 000 - 0 167 Unknown_Attribute -O--CK 100 100 000 - 17 168 Unknown_Attribute -O--CK 100 100 000 - 1 169 Unknown_Attribute -O--CK 100 100 000 - 236 170 Unknown_Attribute -O--CK 100 100 000 - 0 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 173 Unknown_Attribute -O--CK 100 100 005 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 742 184 End-to-End_Error -O--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 014 - 34 (Min/Max 17/39) 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 230 Unknown_SSD_Attribute -O--CK 100 100 000 - 2199023256064 232 Available_Reservd_Space PO--CK 100 100 004 - 94 233 Media_Wearout_Indicator -O--CK 100 100 000 - 0 234 Unknown_Attribute -O--CK 100 100 000 - 16521 241 Total_LBAs_Written ----CK 253 253 000 - 530 242 Total_LBAs_Read ----CK 253 253 000 - 382 244 Unknown_Attribute -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate ||| ____ S speed/performance || _____ O updated online | ______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa7 GPL,SL VS 1 Device vendor specific log 0xde GPL,SL VS 1 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 2 - # 2 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (empty) == 0x05 ===== = = === == Temperature Statistics (empty) == 0x07 ===== = = === == Solid State Device Statistics (empty) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC ``` **_Sorry for the long outputs_** I am not an expert about this data report, so I am providing detailed information for you. According with the long output, Should I assume the SSD is passing away? So far my main concern is the following: ```bash Warning! SMART ATA Error Log Structure error: invalid SMART checksum. SMART Error Log Version: 1 No Errors Logged ``` and ```bash Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged ``` **Note** : Pls, if you find some important point in the result let me know ---
**Author:** ![manueljordan](https://avatars.discourse-cdn.com/v4/letter/m/ecae2f/32.png) [@manueljordan](https://forums.sandisk.com/u/manueljordan)\ **Post date:** [June 11, 2024, 5:20pm UTC](https://forums.sandisk.com/t/what-does-smart-ata-error-log-structure-error-invalid-smart-checksum-mean/319401/2 "2024-06-11T17:20:34Z")
Furthermore was executed the `GSMartControl` tool, with _Extended Self-test_ Once completed, in the `Error Log` tab appears as follows: ```bash Complete error log SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged ``` If is pressed the `View Output` button the report is as follows: ```auto smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.5.0-35-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WD Blue SA510 2.5 1000GB Serial Number: 22196N807187 LU WWN Device Id: 5 001b44 8b08f5266 Firmware Version: 52008100 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 9 11:09:28 2024 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 4 12 Power_Cycle_Count -O--CK 100 100 000 - 1057 165 Unknown_Attribute -O--CK 100 100 000 - 100729639 166 Unknown_Attribute -O--CK 100 100 000 - 0 167 Unknown_Attribute -O--CK 100 100 000 - 17 168 Unknown_Attribute -O--CK 100 100 000 - 1 169 Unknown_Attribute -O--CK 100 100 000 - 236 170 Unknown_Attribute -O--CK 100 100 000 - 0 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 173 Unknown_Attribute -O--CK 100 100 005 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 742 184 End-to-End_Error -O--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 014 - 31 (Min/Max 17/39) 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 230 Unknown_SSD_Attribute -O--CK 100 100 000 - 2203318223361 232 Available_Reservd_Space PO--CK 100 100 004 - 94 233 Media_Wearout_Indicator -O--CK 100 100 000 - 0 234 Unknown_Attribute -O--CK 100 100 000 - 16654 241 Total_LBAs_Written ----CK 253 253 000 - 531 242 Total_LBAs_Read ----CK 253 253 000 - 382 244 Unknown_Attribute -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate ||| ____ S speed/performance || _____ O updated online | ______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3-0xa7 GPL,SL VS 1 Device vendor specific log 0xde GPL,SL VS 1 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 3 - # 2 Extended offline Completed without error 00% 2 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (empty) == 0x05 ===== = = === == Temperature Statistics (empty) == 0x07 ===== = = === == Solid State Device Statistics (empty) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC ``` **Note** : remember in the link of the other post, through the `SMART DATA & Self-Tests...` tool, about the id with 234 (`Uncorrectable ECC Count`) its value is always increasing, so far with **16xxx** sectors, so from that value is reported here the ```auto SMART Extended Comprehensive Error Log Version: 1 (16 sectors) ``` So far the count is around 22xxx (therefore 22 sectors) Again, is my SSD passing away? I am not sure what to do, in these days I am going to go to the hardware provider, to apply the warranty if is necessary, so I am want be very sure the information he is going to give me matches with your answer(s). Thanks for your understanding ---
**Author:** ![Vegan](https://avatars.discourse-cdn.com/v4/letter/v/f07891/32.png) [@Vegan](https://forums.sandisk.com/u/Vegan)\ **Post date:** [June 21, 2024, 10:01pm UTC](https://forums.sandisk.com/t/what-does-smart-ata-error-log-structure-error-invalid-smart-checksum-mean/319401/3 "2024-06-21T22:01:02Z")
The report tells me the disks are working but are close to the end of their service life