Reply
Newbie
Posts: 1
Registered: ‎04-18-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

clayc,

 

best, and most consise, message I found about "Installation Failed, Please Try Again Later" on 1.4.2 install.  

 

Followed the 4 step process of:

 

1 install SanDisk 1.4.1

2 close the dashboard, and in the system tray also

3 install SanDisk 1.4.1  (actually --> Uninstalls  <-- the dashboard)

4 install SanDisk 1.4.2

 

Worked like a CHARM.  I had been beating this beast for 2 hours of reading the forum, installing, uninstalling, looking for registry entries.... AAUUUGGGHHHH!

 

Your right it SHOULDN"T be buried on page 7.

 

Thanks again.

Newbie
Posts: 4
Registered: ‎04-07-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

That worked for me !!!!!!!!!!!!!

Newbie
Posts: 1
Registered: ‎04-20-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

Worked perfectly, thank you...

Highlighted
Newbie
Posts: 1
Registered: ‎04-22-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

The way I got it to work; after 1.4.2 failed, which it removed from the "Programs" list; was to delete the registry key HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\SanDisk  .... Then 1.4.2 installed without any issues ..

 

Newbie
Posts: 2
Registered: ‎01-18-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

Sandisk 1.4.2 installed properly  . . . after havingf the same installation fail 5 times read numerous posts here,  heres how . . . The process requires uninstalling SanDisk DashBoard 1.4.1from the contol panel  . . . . and went went to > This PC > Downloads > uninstalled Sandisk set-up for 1.2.1 then open and installed Sandisk 1.4.2.

In othere word have the set up for 1.4.2 , unistall SanDisk Dashboard 1.2.1 and re install 1.4.2

Please have a basic PC knowledge before performing this operation ,DYOR

Cheers

Newbie
Posts: 1
Registered: ‎04-24-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

This is the procedure worked for me

1. Install 1.4.1

After click finish 1.4.1 will open. Close it and close it from the tray too

2. Again install 1.4.1 - this time install will unistall 1.4.1

3. install 1.4.2

 

Hope it will work for everyone

Newbie
Posts: 1
Registered: ‎04-28-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

Thanks iLDaWg, that worked for me, when I tried installing and uninstalling the previous 1.4.1 version it just seemed to kick off and upgrade and fail.

 

But after I deleted that registry key the installation worked.

Newbie
Posts: 1
Registered: ‎05-15-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

[ Edited ]

Major Geeks does NOT have 1.4.1, that I could find anyways.  

 

Google search comes up dry for downloading 1.4.1.

 

This is the only option that worked for me:

 

Newbie
iLDaWg
Posts: 1
Registered: ‎04-22-2016
 

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

The way I got it to work; after 1.4.2 failed, which it removed from the "Programs" list; was to delete the registry keyHKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\SanDisk  .... Then 1.4.2 installed without any issues ..

 

 
Newbie
Posts: 1
Registered: ‎05-31-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

I've fixed this problem on my laptop. Therefore, I'd like to share my experience here.

 

After clone my system disk to SSD via EZ Gig IV software, I found the Dashboard application can't run properly.

When re-install 1.4.2 version, I also get the same problem.

 

I've tried to delete register keys, but the problem is still observed.

 

I found the Sandisk SSD Dashboard Service is existed on Services List(Control Panel \ Administrative Tools \ Services)

At first, I tried to delete this service via below command:

  sc delete "SanDisk SSD Dashboard Service"

 

Second, I removed the below register key:

  HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\SanDisk

 

Finally, reboot my laptop.

 

After that, I could install the Dashboard appliation without any issue.

Newbie
Posts: 1
Registered: ‎06-03-2016

Re: "Installation Failed, Please Try Again Later" on 1.4.2 install

V 1.4.2 does not install correctly on Windows 10 Pro 64